QSC 6.0 II Manual do Utilizador

1TD-000108-00 rev.A*TD-000108-00*PowerLight SeriesPowerLight 6.0 IIUser ManualTM

10SETUP- Operating Mode SelectionStereo ModeOperating Mode SelectionThe operating Mode selection switch determineshow the inputs are routed to the two

11Parallel ModeBridge ModeIn Parallel Mode, the channel 1 andchannel 2 input connectors areconnected in parallel. Applying aninput signal to either in

12Audio Input ConnectionsCONNECTIONS- InputsInput connections to the PL6.0 II can be madewith XLR, TRS (1/4-inch), or terminal-blockconnectors.The XLR

13XLRCONNECTIONS- Inputs: XLR, TRS (1/4-inch), and Terminal-block PinoutsTRS (1/4-inch)Terminal-block Connectorsphone plug (tip-sleeve)shieldjumper fr

14The DataPort is a QSC-specific connection used for interfacing amplifiers, amplifier monitor-ing devices and signal processors. It is typically used

15CONNECTIONS- DataPort (QSControl users only)Use only QSC AudioDataPort Cables forDataPort connectionsavailable from QSC’sTechnical ServicesGroup..If

16CONNECTIONS- Power Supply Control (Standby/Enable)Remotely Controlling the Amplifier’s Power StatusPower Supply Control 2-pin connector is locatedbe

17CONNECTIONS- Outputs: Binding PostsConnecting the Outputs to the SpeakersUse either the binding post or the Speakon™ output connections. Binding pos

18CONNECTIONS- Outputs: Speakon™ pinoutSpeakon OutputsThe Speakon outputs are for use in Stereo and Parallel operating modes. Minimum speakerimpedance

19USE- AC Power Switch and LED IndicatorsLED Indicators for Power StatusOn the left side of the front panel is the Power switch. The switch is labeled

2© Copyright 2002, QSC Audio Products, Inc.QSC® is a registered trademark of QSC Audio Products, Inc.“QSC” and the QSC logo are registered with the U.

20USE- Signal Level LED IndicatorsLED indicators.USE- Gain ControlsGain ControlsA Gain control adjustment is provided for eachchannel.The voltage gain

21USE- Clip LimitersClip LimitersThe PL6.0 II has separate clip limiters for each channel which respond only to actual amplifier clipping.Amplifier cl

22TROUBLESHOOTINGThe amplifier “cuts-out” when I really crank it up (intermittent operation)-• Make sure the AC power source is rated for the required

23TROUBLESHOOTINGI am trying to use QSC’s DSP-3 or DSP-4 signal processor, but it doesn’t power up when the amp is turned on.What’s wrong?-• Nothing.

24SPECIFICATIONS- PowerLight 6.0 II Electrical DataNote: Specifications are subject to change without notice.Output Circuit Type quasi-complementary M

25APPENDIX-DataPort PinoutThe DataPort connection is QSC-specific. Informa-tion is subject to change.SPECIFICATIONS- PowerLight 6.0 II Electrical Data

26What is PowerWave? PowerWave is QSC's patented power supply technology that not only makes power amplifiers more compact, butalso better soundi

27DisclaimerQSC Audio Products, Inc. is not liable for any damage to speakers, or any other equipment that is caused by negligence orimproper installa

28QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA“QSC” and the QSC logo are registered with the U.S. Patent

3INTRODUCTIONOverview...4Illustrations...

4INTRODUCTION- General OverviewThank you and congratulations on your purchaseof the QSC PowerLight 6.0 II professional poweramplifier. This product re

5INTRODUCTION- IllustrationsFRONT PANEL1- Power switch 4- Gain controls2- Power, Standby, and Protect LEDs 5- Signal, -20 dB, -10 dB, and Clip LEDs3-

6The PL6.0 II is highly durable and is carefully packaged. We recommend youinspect the unit carefully after removing it from the packaging, as occasio

7SETUP- Rack MountingSupporting the Rear of the AmplifierFor mobile and touring use, it is extremely important to support the rear of the amplifier. T

8SETUP- Cooling RequirementsThe PL6.0 II has four rear-mounted variable-speed fans. Fan speed is determined by thetemperature of the amplifier’s inte

9SETUP- AC Power RequirementsAC PowerBefore connecting the amplifier to the ACmains, check the serial number plate toverify operating voltage.The PL6.